PIC17C752, PIC17C756, PIC17C756A, PIC17LC72 and PIC17LC756A are offered in PLCC68- and TQFP64-packages, PIC17C762, PIC17C766, PIC17LC762 and PIC17LC766 are offered in PLCC84- and TQFP80-packages. They do not fit into the 40-Pin-DIL-socket of GALEP.
CONITEC does not offer a special adaptor for these devices so it is up to you to build your own one..
That's what you need:
1.: 40-Pin-DIL-socket,
2.: about 75cm (30 inch) Wire,
3.: Programming-socket ready to accept the device.
4.: appropriate tools
The following connections are necessary for programming these devices:
Signal | GALEP-5-Pin | GALEP-4/3-Pin | PLCC68-Pin | TQFP64-Pin | PLCC84-Pin | TQFP80-Pin |
RA0 | 30 | 26 | 60 | 48 | 72 | 58 |
RA1 | 29 | 25 | 44 | 33 | 56 | 43 |
RA2 | 28 | 24 | 45 | 34 | 57 | 44 |
RA3 | 27 | 23 | 46 | 35 | 58 | 45 |
RA4 | 26 | 22 | 43 | 32 | 51 | 38 |
TEST | 31 | 27 | 17 | 8 | 21 | 10 |
RB0 | 15 | 11 | 59 | 47 | 71 | 57 |
RB1 | 16 | 12 | 58 | 46 | 70 | 56 |
RB2 | 17 | 13 | 54 | 42 | 66 | 52 |
RB3 | 18 | 14 | 57 | 45 | 69 | 55 |
RB4 | 19 | 15 | 56 | 44 | 68 | 54 |
RB5 | 20 | 16 | 55 | 43 | 67 | 53 |
RB6 | 21 | 17 | 47 | 36 | 59 | 46 |
RB7 | 22 | 18 | 48 | 37 | 60 | 47 |
RC0 | 6 | 2 | 3 | 58 | 3 | 72 |
RC1 | 7 | 3 | 67 | 55 | 83 | 69 |
RC2 | 8 | 4 | 66 | 54 | 82 | 68 |
RC3 | 9 | 5 | 65 | 53 | 81 | 67 |
RC4 | 10 | 6 | 64 | 52 | 80 | 66 |
RC5 | 11 | 7 | 63 | 51 | 79 | 65 |
RC6 | 12 | 8 | 62 | 50 | 78 | 64 |
RC7 | 13 | 9 | 61 | 49 | 77 | 63 |
/MCLR | 36 | 32 | 16 | 7 | 20 | 9 |
OSC1 | 23 | 19 | 50 | 39 | 62 | 49 |
VDD | 5 | 1 | 2,20, 37,49 |
10,26, 38,57 |
2,24, 45,61 |
12,32, 48,71 |
VSS | 14 | 10 | 53,68 | 9,25 | 65,84 | 11,31 |
VSS | 35 | 31 | 19,36 | 41,58 | 23,44 | 51,70 |
PLEASE NOTE: The information given cannot be covered by a warranty.
Please always check the position of the pins mentioned using the device's documentation.
We can not offer any warranty covering damage to Galep or the device caused by faulty wiring.